PFAFF SYNCHROTRONIC 1229 SERVICE HOW TO THREAD YOUR

Pfaff Synchrotronic 1229 Service How To Thread Your

If there is conflict or inconsistency between the terms of this document and the additional terms of a particular service the additional terms will only be checked for this conflict or inconsistency.Sewing feetSpecial accessoriesSpecial sewing feetStitch program chartSpool holderStraight stitchThread cutterThread tensionsThreading the needleTop feed indicator lightTrouble shootingUpper threadingUtility-stitch combinationsUtility stitchesUtility-stitch settingWinding the bobbonZigzag stitchHandleiding voor je Pfaff synchrotronic 1229 Naaimachine nodig Hieronder kun je de handleiding gratis bekijken en downloaden als PDF. Huge spares range, parts, feet, needles are held in stock for both new computer embroidery models to the older vintage types.Pfaff sewing machine pfaff synchrotronic 1229 manual. Search our parts database and find the correct spare or accessorys for your Singer, Brother, Pfaff, Bernina, Janome, Husqvarna, Toyota sewing machine. World wide suppliers of sewing machine accessories. Hello, Sandie - You will find several images of how to thread your Pfaff Synchrotronic 1229 sewing machine in the instruction book for the machine, starting on Pages 6 - 9 (PDF images 10 - 13) of the manual.

Be careful when sewing that yourfingers will not be injured by theneedle.2. The Stopmatic control raises the needle(for threading, bobbin winding and removing the work).2 Sewing foot3 Sewing foot holder4 Needle threader5 Needle threader control6 Needle thread tension7 Take-up lever8 Hinged top cover9 Carrying handle10 Hand wheel11 Thread guide12 Second (detachable) spool holder13 Spool holder with swivel arm14 Master switch15 Top speed selector slide16 Needle holder with screw17 Control for reverse sewing andDropping the feed dog18 Needle plate19 Lid containing spare bobbins20 Pattern start selector wheel21 Bobbin winder22 Pattern length selector wheel23 Utility- and ornamental-stitchButtons24 Master selector dial25 Needle position and buttonholeKnob26 Buttonhole control27 Base plate28 Free arm cover, enclosing sewingHook29 Free arm30 Thread guide31 Thread guide32 Thread guide for bobbin winding33 Accessories34 Bobbin thread retainer stud35 Stitch chart36 Top feeding foot with thread(on back of machine arm)38 Bobbin thread monitor39 Bobbin winder indicator light40 Top feed indicator light41 Eraser button1. Is dit niet de handleiding die je zoekt, neem dan contact met ons op.1 Detachable work support withaccessory compartmentesser bar litter andStopmatic control ver 37 has four positions: Sewing foot is raised.

The accessories:urther contain: 2 unreeling discs, P forSmall spools, and P + 0 for large spools.These are pushed on the spool pin in ironof the spool of thread.Accessory compartment (33)The illustration below shows how toarrange the snap-on feet in thecorn partrnent:o = darning foot1 = clear-view sewing foot2 = overlock foot3 = blindstitch foot4 = zipper foot5 = buttonhole footThe normal sewing foot is fitted to thesewing foot holder.Ectrical connection and foot controlIl the cord out of the foot control andsh plug M into the machine socket.ace the foot control under the table, asown.ush power cord plug K into the machine)cket and plug L into the wall socket.ress master switch 14 (page 4). It is pushed over the wire (N)nd onto the holder (0). There is a s$itch chart with stitch5ettings inside the cover.Spool holderSpool holder 13 can be swung to twoositions:= For bobbin winding and replacingthe carrying case cover.- = For sewing.second spool holder(is included in theAccessories. To place sparebobbins in the lid, tilt it back (P).Opening the hinged top coverold carrying handle 9 to the rear, thenpen hinged top cover 8 by swinging itDack. Lift the worksupport off (N) and open its lid (0) toaccommodate accessories.

The indicator light goes out when afull bobbin is inserted and sewing isresumed.Important: Free arm cover 28 must be kepclosed.Bobbin winder indicator light anddisengaging the sewing mechanismThe yellow indicator light 39 lights upwhen the presser bar lifter is set at theStopmatic position (K on page 5). Your machine isnow ready for sewing.Electronic top speed selectorWhen slide 15 is pushed towardthe machine sews faster, when it ispushed toward , it sews slower.The piercing power of the needle remainsthe same, regardless of the machinespeed.Bobbin thread monitorThe red bobbin thread monitor 38 starts tcflash when the bobbin thread is runningout. If theachine does not start, release the footntrol, then press it down again.To replace the cord in the foot control,pull it slightly, then release it, and it willrewind into the control automatically.Master switchPress master switch 14.

The yellow indicator light 39lights up. The bobbin cannot fall out as longas you keep latch K raised.Winding from a second spoolRaise presser bar lifter 37 to its horizontal(K) position. Lift latch K and take out thebobbin. The StopmaticControl raises the needle (for needlethreading, bobbin winding andremoving the work).= The sewing foot is raised (for turningthe work).= The Stopmatic control raises theneedle (for basting).Removing bobbin case and bobbinRaise the needle, and open free arm cover28.

Wind afew turns of thread on the bobbinclockwise. Pull the thread from thespool, pass it through guides 11 and 32,counter-clockwise around retainer stud 34,and then to the bobbin winder. Push asuitable unreeling disc M on the spool pin.Place a bobbin on spindle 21 so that pin Kenters slot L.

Draw the needle thread underthe sewing foot, to the left and up intoguide 32. The yellow indicator light 3lights up. Remove the bobbin and cut thcthread.Winding through the needle eye(only when a metal sewing foot is fitted)Raise presser bar lifter 37 to its horizonta(K) position. If you want to stop thebobbin winder earlier, pull lever 8forwards. The bobbinWinder stops automatically when thebobbin is full.

However in slot Kone thread is placed above disc L, theother below it, and at needle holder 16,one thread is pulled through the rightguide, the other through the left.Twin needles are threaded by hand.Threading the needleaise the presser bar lifter to theorizontaI (Stopmatic) position. The large unreeling disc isalways used together with the small one.Pull the thread from the spool and draw itinto thread guide 11, slot K, thread guide31, take-up lever 7, thread guide 30 andthe right guide of needle holder 16.Note on twin needlesFor two-needle sewing jobs attach thesecond spool holder for the second spoolof thread (page 2).Both threads are passed through thethread guides together.

2021.12

Trim Enabler In Windows 7

Pfaff Synchrotronic 1229 Service Manual